Welcome to this video
Raise the lower the steering wheel press the small pedal the angle of the steering column Is Altered by First
An integer is required
Here in front of the driver is the instrument panel with the tachograph to the right the central warning lamp to light up
To draw the driver's attention to functional fault
The button on the left of the warning lamp panel is used to check that the warning indicator lamps off
Functioning properly each lamp has a symbol and colour to indicate its specific function
Symbols can be found in the instruction manual let state the coolant level warning lamps as an example
The yellow warning lamp indicates that the cooling system needs to be topped up if the engine is running at
Red warning lamp comes on a buzzer to as heard this means that the coolant level is dangerously low and has to
Immediately the driver information system constantly monitors the trucks most
Open functions is during a warning of any function shows signs of a normal behaviour
When the ignition key is turned to the driving position the warning lamps light up for about 3 seconds
The left side power window lift
Differential lock and air conditioning the cabin fan must be on for the air conditioning system
Adjusting the rear view mirrors and right side power window
If revert by spring action to the driving position
The indicator lamp shows that
3 heater element in the inlet manifold is activated automatic preheating takes up to 50 seconds
Depending on the temperature of the coolant after which the indicator lamp goes out
Is equipped with EDC so started without pressing the accelerator pedal just turn the key to the starting position
Add stop the engine as you can see the indicator lamp lights up once
Add a second preheating phase begins automatically if the weather is particularly cold and there is
Google exhaust smoke you can use the preheater one small eating of the inlet air helps the engine too
I did also reduces the amount of smoke which always forms when a cold engine is fired up engine
There is also reduced as you probably realise you should never use a quick start spraying
Volvo engine equipped with an electrical preheater since this may cause an explosion in the inlet manifold
A cold engine should never be red hard immediately after start is very thick
Gold and does not flow easily so both the engine and the turbocharger can easily be damaged by high revs
If I pressure does not have time to stabilise
5600 RPM for about a minute press the brake pedal until the EDC systems diagnostic
Lamp goes out
Increase engine speed to about 1000 RPM using the EDC control when the controllers moves towards me
The pre-programmed engine speed will be set at 1000 RPM allow the engine to warm up for another
10 minutes reset the engine speed by moving the control to off by pressing the exhaust brake
Recocash pedal when driving the EDC control can be used as a
Control unit moves upwards to program the current road speed if you break the
What facility is cancelled to return to the previous cruising speed movements took towards resume
With the cruise facility activated it is possible to increase or decrease road speed by me
Upwards or downwards
Brake pressure front and rear engine oil pressure
Engine oil temperature coolant temperature
Exhaust temperature
Oil temperature battery charge temperature
You will level ready to drive off the truck is on a level road and gross
Google why does approximately 20 times the appropriate gear for moving off
Direct me to III
Location of the range unit and 2/4 which occupies the same position as 1st gear in The Selector Gate
Low gears and under firm acceleration there is no harm in allowing the engine to rev
The green Center on the computer
And now is the time to use the splitter to V high
From V high preselect low splitter
When you change gear you'll be in 6 low after reaching your cruising speed save fuel by
The engine speed within the green set on the rev counter
3 select the next splitter change press the clutch
6ty is engaged
After refueling
You know from experience that you will need to change down at least twice wait until the engine restaurant about
100 RPM
When you get to the Brow of the Hill accelerator
The rest
The weight of the truck results in acceleration down the slope so now it's
Used exhaust brake engine speed is now in the blue section of the rev counter never let
Touch the red sauce to reduce road speed and then lift it off
Brake pedal to let the brakes cool down repeat this procedure is necessary while keeping the needle in the blood
Connect to the whole time this is necessary in order to keep the correct engine speed