the Mac pres PC project was made possible by Squarespace
then
the what is a bi's eddie Van Dec stores and I'm back today to show you guys how
to build your very own computer
the PC we are building today consists of work station parts for a mattress PC
project but this guy should help you out regardless of what PC you are trying to
build
the only two years essentially going to need to build the PC is the screwdriver
but of course I'm some common sense can help smoothen out the process
alright so let's start by placing the CPU onto the motherboard
by lifting these two latches we release the tree and see the pains and they're
needed
and now be sure not to touch these as they are very fragile and can
easily be damaged next take the CPU Adam its protective enclosure by making sure
not to touch the top buoyed up by Tom
and basically just hold a bite sides we're going to match the golden triangle
that is on the CPU to the one that is on the motherboard
when placing a CPU down be sure not to move it around or apply any pressure to
it as it can damage the hands
just basically said it down and it should fall right into place
if it doesn't fit properly then you probably put it in the long way so make
sure you double check everything
I before moving on so after you successfully install the CPU into the
CPU socket we can then secured the latches
there's gonna be some pressure here but it's completely normal so %ah
do not freak out next it's time to put in the RAM
now is a good time to refer to your motherboard manual to see where you
place your RAM sticks
ideally if you have more than one Rams the you have to place them in the same
colored
slots on the motherboard and you man you should show you exactly which ones
moving forward make sure you release the tab on the motherboard seen here to put
in the RAM
also make sure that the notches at the bottom with the RAM correspond to data
the motherboard
and gently press down on the ramp stick until it snaps in place
now we are going to mount the motherboard into our case
but first we're going to have to install the motherboard standoffs to make sure
the motherboard is not touching their mettle you need to know which owes to
install the standoffs on so what we did was basically
hell the motherboard over the case for a few seconds to get an idea which cause
we're going to use
after standoff have been installed you can install the motherboard backplate
a Kaio shield and here you basically just aligned correctly to the back and
snap into place it's actually really simple
after that you are ready to place the motherboard back in that case I want to
do that make sure the connections are visible
do with a back in FB are you can proceed
after that you continue to install the screws into your motherboard
make sure to tighten them any criss-cross pattern to even at the
stress on the motherboard
do not pain and too hard Justin up until the screw stopped raining
without forcing them next we're going to be installing the power supply and
basically straightforward
all I had to do was lining up with the holes at the back in your case
and then find the there's a need power supply screws that came with UK singer
starts growing them
in you may need to hold the power supply up using your other hand to ensure that
the schoos go inch
rate and after that we are going to be installing the CPU cooler
be well with an aftermarket Noctua cooler for build
but they are all usually the same when it comes to installation however you
should always check because manual
for more information make sure you are using the correct supplies for the type
a CPU you're using
and then we're going to be screwing in the CPU cooler standoffs in the
designated areas
after now we're gonna be placing in the mounting brackets based on how we wanna
f low:
and then finally we're gonna be using this supply both the security in the
mounting brackets in place
to screw in the Noctua cooler to place we are going to have to take out one
other fans in order to access the tightening points
this is done by pulling the latches on each side allowing for the removal of
stuff and
after that we are ready to spread the supplied thermal compound and the CPU
and depending on what cool you are using
it may or may not come be applied with thermal compound
so the call is manual suggests only around forty five millimeters up thermal
paste
you definitely don't want to overdo this part because it can cause problems with
the cooler
so you can use the same amount that we use you in a video because when you
place the coup on top you will spread evenly covering the entire surface have
the CPU
after you are though the thermal compound place the CPU cooler on top at
the CPU
and begin tightening the screws which will secure it in place
after that you can install the fam back into its spot in finally we are ready to
plug the CPU cooler into the CPU fan header on the motherboard
if you guys aren't sure where exactly to plug this in refer to your motherboard
manual
and it will show you where
next up we're gonna be routing the 24 pin cable from the power supply to the
24-pin slot on the motherboard
then we're going to the same thing 48 pin connector which is also from the
power supply
once again if you guys can find the slot on the motherboard then refer to your
manual for some help
next we're going to install the graphics cards be sure to remove the metal
brackets from the slots that you are going to use
and then slide the video card and you should hear it snap in place
always install your video card on the first PCI slot for better performance
anything as at two graphics cards now's a good time to install the SLI or
crossfire bridge
it so this is what your PC should relatively look like once all those
components are installed correctly
you can take the time now to make sure everything is securely fitted before
moving on
I'm after that we are going to install a PCI card into the PCI slot on the bottom
here
if you guys don't have a PCI DSS the card then you gonna be skipping this
step
now to get some cables out at the way first we're going to plugin the USB 3
cable that runs from the top at the case into the motherboard
usb3 header then where do the same team with the USB two cables
and finally we are going to plug in everything that is located at the front
panel including the hard drive activity LED
and the power switch are a sous motherboard actually came a convenient
way to plug in all these wires to the motherboard
if you as the not come with something like this then you are going to have to
plug them in
one by one next plug in all the cables the power supply including the PCA
cables a plug into your graphics cards
and make sure you're plugged in all the fans and that there are no more
connections left to make
and that should be everything as far as installing the hardware is concerned
one thing you should do after installing the parts is to put up UPC make sure
everything is running fine
and that your BIOS screen shows up after that the next step would be to install
the operating system and the drivers which should be fairly straightforward
so I won't go through them there's plenty for the videos on YouTube with
that
and but if this video helped you guys out then please leave a like and if it
didn't leave a comment with your questions or concerns
and I will do my best to answer them quickly this workstation PC will be
going head to head with the Mac Pro six core model
and we will be running benchmarks rendering files and a few other test to
see which PC performs the best
with the scene costs of that sounds like something that interests you don't feel
free to stick around
so before I head out I want to thank the people ask where space for making his
entire project possible Squarespace makes it really easy to create your very
own website for online portfolio
in fact we create our own website XO star TV using Squarespace in less than a
day
in a turn out exactly how we wanted to the F so many beautiful campus to choose
from to match your needs or you can even start from scratch like we did
everything his drag and drop so you don't need to know anything about
calling at all
and square space really cares about the design so all their templates are
extremely clean
and allow your content to be the focus are your website
what's also cool is that your website even skills to look amazing
on mobile devices also starting from today all Squarespace plans now support
commerce functionality
which means that you can sell products online no matter which
plan you choose the best part about all this data speed to try
seriously guys go ahead and tried up fourteen days in Cebu like it
all you need is you name email and password no credit card is required any
guys
end up loving it which I'm sure you will you can use the Kotex or stoop or 10
percent of their already super-low
prices this is that from Pak source and I'll see you next time
ok
on